BlackTop Topcoat 500mls
BlackTop is a permanent, moisture-cured, UV stable coating primarily used for topcoating surfaces previously sealed with RustSeal or any other paint/primer application. BlackTop is a high performance protective coating specifically formulated to withstand dulling and fading caused by prolonged sunlight exposure. BlackTop may be used alone as a resilient coating but it will not offer the ultimate rust protection unless it is used in combination with RustSeal. For the best stop rust & ultraviolet protection, first apply RustSeal to permanently seal the surface and then topcoat with BlackTop for an incredibly tough and professional looking finish. Like RustSeal, BlackTop dries to a rock hard yet flexible coating that can be readily applied to chassis, coil springs and light weight panels. BlackTop also has high heat resistance and can be applied to almost all automotive applications except exhaust systems. Satisfaction guaranteed!

$55.47(inc GST)

BlackTop Topcoat 1litre

$91.64(inc GST)

BlackTop Topcoat 4litres

$289.40(inc GST)

Galvanised Steel 1litre
RustSeal Galvanized Steel Introducing our newest RustSeal colour ... GALVANIZED STEEL! We've replicated the look of an industrial galvanized matte finish with this new colour formula of RustSeal, while enhancing the UV stability. RustSeal Galvanized SteelThe Galvanized Steel colour can be used in all the same applications as our original RustSeal colours, but is particularly suited for industrial applications where a rapid build of a rust protective coating is needed to smooth and level rough surfaces, without gassing or sagging. The RustSeal Galvanize Steel Advantage is that it is 3 products in 1 ... a permanent rust preventive coating, a high build primer, and a UV enhanced topcoat! Use Galvanized steel in conjunction with AquaKlean & RustBlast for the most complete rust prevention system available today!

$71.14(inc GST)

Galvanised Steel 4litrres

$223.08(inc GST)

DiamonWhite Topcoat 500mls
KBS Diamond Finish is a permanent high solids moisture curing custom Topcoat. Diamond Finish is the latest development in ultra high performance topcoats with very high solids (over 60%) and low VOCs. Diamond Finish once cured is incredibly tough and hard like no other clear coat you have ever used. This glossy topcoat remains permanently flexible and is able to perform in the toughest environments including Australia’s highest UV applications without yellowing or cracking. Diamond Finish can be applied by brush (without leaving brush marks), roller and conventional spray gun easily and unlike normal 2 Pak coatings no hardener is needed! Just stir and go! Diamond Finish Clear Coat will cure without heat or UV lights in temperatures from 6C to 30C. Diamond Finish can be applied directly to cured Automotive and industrial primers and standard solid colour paints. Diamond Finish is able to withstand the harshest of chemicals including, fuels, solvents, Battery acid, Brake fluid, Ethanol, Methanol, MEK, Hydrochloric Acid, Fertilizers, and Acetone. And because Diamond Finish is so resistance to these materials it means Graffiti just won’t stick, and can be removed simply with a solvent soaked rag. Diamond Finish is able to perform in the high temperature automotive applications including the use on cylinder heads, engine blocks, brake components even inlet manifolds, without yellowing up to 155 C.

$61.50(inc GST)

DiamonWhite Topcoat 1 litre

$95.26(inc GST)

DiamonWhite Topcoat 4 litres

$313.51(inc GST)

DiamonClear Topcoat 500mls
KBS DiamondFinish ClearCoat is a permanent high solids Clear Coat. It is the latest development in ultra high performance clear coats with very high solids (over 60%) and low VOCs. DiamondFinish ClearCoat is incredibly tough and hard like no other clear coat on the market. This water clear high gloss clear coat remains permanently flexible and is able to perform in the toughest environments without yellowing, cracking or peeling. DiamondFinish ClearCoat can be applied with a brush (without leaving any brush marks), roller and conventional spray gun. Unlike normal two part coatings, no hardener is needed. You can just stir and go. DiamondFinish ClearCoat will cure without heat or UV lights in temperatures from 50° to 86° Fahrenheit. DiamondFinish ClearCoat can be applied directly to a cured Automotive basecoat, Standard solid color paints, and Single Part or Two Part paints. It can also be applied to Non Ferrous metals including Aluminum, Alloys, Brass, Chrome and Copper. DiamondFinish ClearCoat is able to withstand the harshest of chemicals including fuels, solvents, Battery acid, Brake fluid, Ethanol, Methanol, MEK, Hydrochloric Acid, Fertilizers, and Acetone. Because DiamondFinish ClearCoat is so resistance to these materials, that means Graffiti just won't stick and can be removed simply with a solvent soaked rag. DiamondFinish ClearCoat is able to perform in the high temperature automotive applications including the use on cylinder heads, engine blocks, brake components and even inlet manifolds, without yellowing up to 325° Fahrenheit. It’s technology that’s unbeatable! Satisfaction guaranteed!

$61.50(inc GST)

DiamonClear Topcoat 1 litre

$95.26(inc GST)

DiamonClear Topcoat 4 litres

$313.51(inc GST)